Why a floor plan that looks right can still be 200mm out
A plan is a set of dimensions, not a picture. Where the millimetres go missing, a worked check on a 3.6m room, and how to tell a drawing that will build from one that will not.
A floor plan is not a picture of a room. It is a set of dimensions that happens to have furniture in it, and the drawing only works if every line is at true scale and every dimension agrees with the line it sits on. Most plans that fail on site fail that test in a way that is invisible on screen: the drawing looks right, the numbers are a little off, and the error only appears when something has to fit.
Where 200 mm goes missing
The classic error is measuring between one pair of faces and drawing between another. Take a room quoted internally at 3,600 mm:
| What you draw to | Dimension |
|---|---|
| Plaster face to plaster face (internal) | 3,600 |
| Stud to stud (89 mm stud, 12.5 mm board each side) | 3,625 |
| Face of stud wall to face of stud wall, external | 3,828 |
So the same room is 3.6 m, 3.625 m or 3.828 m depending on which faces the dimension refers to. Draw the internal figure but set out the walls to the external line and every wall in the building is 114 mm out of position — not enough to notice on a plan, plenty to notice when the staircase arrives.
Two habits prevent it. Dimension to the face you actually build to, and say which face that is, once, on the drawing. And chain the dimensions so they add up: a run of rooms plus partitions, totalled, must equal the overall figure on the outside of the plan. If the chain does not close, one of the numbers is wrong and it is cheaper to find out now.
Blocks only help if the geometry is right
A library of blocks saves hours, and it can spread a mistake across every drawing in the set. Four things to check the first time you use any library:
Units. Millimetre drawings with imperial blocks are the classic failure — a 762 mm door drawn as 762 units in a millimetre file looks like a door and is the wrong size by a factor of 25.4. Check one known block against a known dimension before you trust the set.
Scale. A block inserted at a scale other than 1:1 in model space is a drawing that will measure wrong for everyone downstream, including the person who sets it out.
What the block represents. A 762 mm door leaf is not a 762 mm structural opening. The frame, the linings and the tolerances add up to an opening that is around 800–810 mm for a standard internal door. Drawing the leaf and treating the block edge as the opening is a 40 mm error per doorway — which, on a corridor of six doors, is a quarter of a metre.
Layer discipline. Blocks on named layers, at true scale, in millimetres, with the swing shown in the direction the door actually opens. A plan where every door swings the same way is a plan nobody checked.
The fit check
The reason to draw to true scale is that the drawing can be tested before anything is ordered. A kitchen run on a 3,000 mm wall:
- Five 600 mm units = 3,000 mm exactly. On a wall that measures 3,000 on the drawing, that fits only if the wall is perfectly straight, the plaster is perfectly flat and the corner is perfectly square. None of those are true.
- On a 2,980 mm wall, the fifth unit does not go and the design has to change.
- Add filler panels and the usable run drops to about 2,900 mm — four units and 500 mm of something.
That arithmetic takes a minute on a dimensioned plan and takes a week of recriminations after the kitchen is delivered. It is also the reason a plan drawn “near enough” is worse than no plan: it invites decisions that cannot be undone.
Planning drawing, construction drawing, and the difference
A drawing submitted for planning approval and a drawing someone builds from are different documents with different jobs. Planning drawings show use, siting, scale, appearance and access — the current rules for England are at GOV.UK — planning permission. Construction drawings carry the dimensions, levels, construction detail and notes that a trade needs, and where the work falls under the building regulations, the detail has to satisfy the approved documents — see GOV.UK on building regulations approval.
Sending a planning drawing to a joiner and calling it a construction drawing is a common, expensive shortcut. The joiner will build what is drawn, and what is drawn is a massing diagram.
Checking a plan you were handed
Four questions, in this order: does the dimension chain close; is there a stated convention for which face dimensions are taken to; do the openings match the doors and windows specified; and does anything actually have to fit — a stair, a kitchen, a bathroom — have its own dimension check on the drawing. If any of the four fails, the plan is a sketch with walls on it.
The library behind this page is 24 metric blocks at true scale — doors, windows, sanitaryware, stairs and kitchen units — drawn in millimetres with named layers, in DXF so they open in whatever you already use.
General information only, not tax or financial advice. Every guide links to the current GOV.UK page for the rules it applies.